Have no idea
Posted: 24. Jun 2020, 02:57
- 106005244_883565398819198_5092041829923688693_n.png (33.91 KiB) Viewed 526 times
Page 1 of 1
no matter what I try to install all virtual machines hang on install and stop with this Any help would be greatly appreciated.
Re: Have no idea
Posted: 24. Jun 2020, 15:00
You see the green turtle in the status bar? Most likely you have Hyper-V running. A guest log would confirm.
Start the guest from full normal shutdown, not save-state. Run until you see the problem happen, then shut down the guest from within the guest OS if possible. If not possible, close the Virtualbox window for the guest with the Power Off option set.
Right-click the guest in the main Virtualbox window's guest list, choose Show Log. Save the far left tab's log, zip it, and post the zip file, using the forum's Upload Attachment tab.
Before you post the log, look for these lines:
If you find them ('VT-x' might be 'AMD-V', but it's the same cause), then a service that uses Microsoft Hyper-V is running on your host PC. Normally Hyper-V blocks Virtualbox. But your PC is of the type and OS where Virtualbox can attempt to run the guest using the Hyper-V engine. This arrangement is still being developed and isn't 100% yet.
If VirtualBox is running without Hyper-V enabled, and nothing else is interfering with hardware virtualization (VT-x / AMD-V), then the usual virtualization icon (
) will be seen in the Status Bar.
To turn Hyper-V off completely, do this:
1. Shut down all programs. You will have to reboot your host.
2. See I have a 64bit host, but can't install 64bit guests. This tutorial has a couple more things to look for in step 2. Be sure these are all turned off.
3. Find the Command Prompt icon, right click it and choose Run As Administrator.
4. Enter this command:
If your Virtualbox does not start successfully, zip and post another vbox.log. For further info, see https://www.tenforums.com/tutorials/139 ... puter.html
If you found the telltale lines you can skip posting the log unless you can't get the green turtle to go away.
Start the guest from full normal shutdown, not save-state. Run until you see the problem happen, then shut down the guest from within the guest OS if possible. If not possible, close the Virtualbox window for the guest with the Power Off option set.
Right-click the guest in the main Virtualbox window's guest list, choose Show Log. Save the far left tab's log, zip it, and post the zip file, using the forum's Upload Attachment tab.
Before you post the log, look for these lines:
{timestamp} HM: HMR3Init: Attempting fall back to NEM: VT-x is not available
{timestamp} NEM: WHvCapabilityCodeHypervisorPresent is TRUE, so this might work...If you find them ('VT-x' might be 'AMD-V', but it's the same cause), then a service that uses Microsoft Hyper-V is running on your host PC. Normally Hyper-V blocks Virtualbox. But your PC is of the type and OS where Virtualbox can attempt to run the guest using the Hyper-V engine. This arrangement is still being developed and isn't 100% yet.
If VirtualBox is running without Hyper-V enabled, and nothing else is interfering with hardware virtualization (VT-x / AMD-V), then the usual virtualization icon (
) will be seen in the Status Bar.To turn Hyper-V off completely, do this:
1. Shut down all programs. You will have to reboot your host.
2. See I have a 64bit host, but can't install 64bit guests. This tutorial has a couple more things to look for in step 2. Be sure these are all turned off.
3. Find the Command Prompt icon, right click it and choose Run As Administrator.
4. Enter this command:
bcdedit /set hypervisorlaunchtype off
5. Enter this command: shutdown -s -t 2
6. When the computer turns off, unplug it for 20 seconds. Then plug it in again and boot up Windows 10. If your Virtualbox does not start successfully, zip and post another vbox.log. For further info, see https://www.tenforums.com/tutorials/139 ... puter.html
If you found the telltale lines you can skip posting the log unless you can't get the green turtle to go away.