virtualbox.org

hello,
my system fails to boot as it cant be attached due to a uuid mismatch. here is the error:

01:07:04.420000 ERROR [COM]: aRC=VBOX_E_OBJECT_NOT_FOUND (0x80bb0001) aIID={22781af3-1c96-4126-9edf-67a020e0e858} aComponent={SessionMachine} aText={No storage device attached to device slot 0 on port 0 of controller 'IDE'}, preserve=false
01:07:04.420000 ERROR [COM]: aRC=VBOX_E_OBJECT_NOT_FOUND (0x80bb0001) aIID={22781af3-1c96-4126-9edf-67a020e0e858} aComponent={SessionMachine} aText={No storage device attached to device slot 0 on port 1 of controller 'IDE'}, preserve=false

01:08:20.627000 ERROR [COM]: aRC=E_FAIL (0x80004005) aIID={29989373-b111-4654-8493-2e1176cba890} aComponent={Medium} aText={UUID {75f12308-5cdd-46b7-8207-6f937fc3a772} of the medium 'D:\VirtualBox VMs\Server 2008 R2\lab1.vdi' does not match the value {f017bfc2-84cd-4b88-89cb-476a139d0571} stored in the media registry ('C:\Users\epasho/.VirtualBox\VirtualBox.xml')}, preserve=false

The UUID was changed in order to increase the disk size but that did not work either so i am stuck with a faulty disk
any ideas how to fix this?

Thanks

Remove the Disk from the known Disk list in the Media Manager, then try again to add it.

i tried that but does work. attached is the screen capture

If it shows up in the list it means you did not remove it from the Media Manager.

It should be possible to just attach the new vdi in Storage Settings of the VM.

It is, but since you changed the hard disk without telling Virtualbox properly about it, it is now not letting you so there are no mistakes.
You need to manually unregister the old disk prior to using the new one.

If you look at the screen shoot, i am trying to create a new virtual and use existing vdi. that's the problem cant reuse the vdi disk.

If the disk is showing as inaccessible then it likely the disk with the expected name and UUID has been moved or deleted since it was registered. You need to unregister it, and prior to VirtualBox v4.3.2, you need to shut VBox down for 30 seconds before trying to register another medium with the same name or UUID.

When you register media in VirtualBox you are saying "this is where you can find this disk from now on". It's up to you to keep to your side of that deal.

noteirak wrote:It is, but since you changed the hard disk without telling Virtualbox properly about it, it is now not letting you so there are no mistakes.
You need to manually unregister the old disk prior to using the new one.

That's correct, i am able to remove storage setting but still detects the old setting...
How can i remove it manually? Sorry, i am very unfamiliar with the Virtual Box commands. Please be more specific.

Endrit

Before we answer any more questions, please provide basic diagnostic data such as VirtualBox version. See Minimum information needed for assistance.

mpack wrote:Before we answer any more questions, please provide basic diagnostic data such as VirtualBox version. See Minimum information needed for assistance.

Memory size: 2048MB
Page Fusion: off
VRAM size: 32MB
CPU exec cap: 100%
HPET: off
Chipset: piix3
Firmware: BIOS
Number of CPUs: 1
Synthetic Cpu: off
CPUID overrides: None
Boot menu mode: message and menu
Boot Device (1): DVD
Boot Device (2): HardDisk
Boot Device (3): Not Assigned
Boot Device (4): Not Assigned
ACPI: on
IOAPIC: on
PAE: off
Time offset: 0ms
RTC: local time
Hardw. virt.ext: on
Hardw. virt.ext exclusive: off
Nested Paging: on
Large Pages: on
VT-x VPID: on
State: powered off (since 2013-11-22T16:34:00.000000000)
Monitor count: 1
3D Acceleration: off
2D Video Acceleration: off
Teleporter Enabled: off
Teleporter Port: 0
Teleporter Address:
Teleporter Password:
Tracing Enabled: off
Allow Tracing to Access VM: off
Tracing Configuration:
Autostart Enabled: off
Autostart Delay: 0
Storage Controller Name (0): IDE
Storage Controller Type (0): PIIX4
Storage Controller Instance Number (0): 0
Storage Controller Max Port Count (0): 2
Storage Controller Port Count (0): 2
Storage Controller Bootable (0): on
IDE (0, 0): D:\VirtualBox VMs\Server 2008 R2\lab1.vdi (UUID: f017bfc2-84cd-4b88-
89cb-476a139d0571)
IDE (1, 0): D:\ISO\VS2010UltimTrial.iso (UUID: 1e52170a-9dc9-4f2f-a681-79618eafb
3f2)
NIC 1: MAC: 08002712CBEA, Attachment: Bridged Interface 'Intel(R) 8257
9LM Gigabit Network Connection', Cable connected: on, Trace: off (file: none), T
ype: 82540EM, Reported speed: 0 Mbps, Boot priority: 0, Promisc Policy: deny, Ba
ndwidth group: none
NIC 2: disabled
NIC 3: disabled
NIC 4: disabled
NIC 5: disabled
NIC 6: disabled
NIC 7: disabled
NIC 8: disabled
Pointing Device: PS/2 Mouse
Keyboard Device: PS/2 Keyboard
UART 1: disabled
UART 2: disabled
LPT 1: disabled
LPT 2: disabled
Audio: enabled (Driver: DSOUND, Controller: AC97)
Clipboard Mode: disabled
Drag'n'drop Mode: disabled
VRDE: disabled
USB: enabled
EHCI: disabled

USB Device Filters:

<none>

Available remote USB devices:

<none>

Currently Attached USB Devices:

<none>
Bandwidth groups: <none>
Shared folders: <none>
VRDE Connection: not active
Clients so far: 0
Guest:
Configured memory balloon size: 0 MB

C:\Program Files\Oracle\VirtualBox>

Virtual box Version: 4.2.16 r86992
Host info:
Intel Core i7-3770 cpu 3.40ghz
RAM: 16gb
System type:64-bit

epasho wrote:Virtual box Version: 4.2.16 r86992

So do the 30 second shutdown like I said before.

thanks for the quick reply mpack, but still the same issue.
any other ideas?

Thanks

problem has been fixed. All needed to be done was to set uuid to the old one like this:

C:\Program Files\Oracle\VirtualBox>VBoxManage.exe internalcommands sethduuid "D:
\VirtualBox VMs\Server 2008 R2\lab1.vdi" f017bfc2-84cd-4b88-89cb-476a139d0571
UUID changed to: f017bfc2-84cd-4b88-89cb-476a139d0571

reference:
viewtopic.php?f=8&t=50639

thanks

Great! Would you mind changing the original post's title to "[SOLVED] updating uuid" so that the rest of the community can benefit as well from your findings? TIA.