Only Half Cores used; over half cores> Guru Mediation error
Posted: 2. Sep 2012, 20:58
Hello,
I have been getting this Error Guru Meditation constantly now when I rush the VM to start. Only a complete Server reboot of r2 fixes this.
I have 80 Cores 4 E7-8860, 64 Gigs dd3 1066 ECC. When using Win7x64 Guests of 2 gigs ram/ 5 cpus each/ she will work ONLY if I load each VM one completely at a time. After around 10 VM have completely loaded the rest of VMs fail with Guru error. Thinking out of resources since I was able to load with no problems.
When I try to load 15Vms all fast and at once, I don't get past the 3rd VM. All crash at the same time with Guru Error. Can't retry it either unless a full reboot.
I looked in the logs and found that only half of my CPU cores are registered which would explain the 50% cpu load max then crash. I was not able to get above 50% Cpu load however my ram was a stable slow 45 degree climb (Task Mgr) with half left over.
In the Log files of the Guests Win 7x64: Logical Host Processors: 40 Present, 40 Max, 40 Online, mask 000000fffffffffffff
I know win 7 has a limitation of 2 CPU which would make total sense since its only seeing 2 cpus. My question is does VB allocated CPUS based upon the host or guest or both?
I'm just trying to figure out the crashes. It appears if set the CPU and Ram parameters Vs the number of VM max per system using only half the CPUS .........she works.
Also Numas 1,3 active, Numa Mode 2,4 not even used. Even if i set tasks to high priority and set affinity to all cores same result.
System is running very fast and stable when the number of CPU was lower but this crash is a concern. last line (VT-x is not available) I'm think because I have no CPU cores left.... which again runs out of CPU cores causing error.
Thanks,
Mike
I have been getting this Error Guru Meditation constantly now when I rush the VM to start. Only a complete Server reboot of r2 fixes this.
I have 80 Cores 4 E7-8860, 64 Gigs dd3 1066 ECC. When using Win7x64 Guests of 2 gigs ram/ 5 cpus each/ she will work ONLY if I load each VM one completely at a time. After around 10 VM have completely loaded the rest of VMs fail with Guru error. Thinking out of resources since I was able to load with no problems.
When I try to load 15Vms all fast and at once, I don't get past the 3rd VM. All crash at the same time with Guru Error. Can't retry it either unless a full reboot.
I looked in the logs and found that only half of my CPU cores are registered which would explain the 50% cpu load max then crash. I was not able to get above 50% Cpu load however my ram was a stable slow 45 degree climb (Task Mgr) with half left over.
In the Log files of the Guests Win 7x64: Logical Host Processors: 40 Present, 40 Max, 40 Online, mask 000000fffffffffffff
I know win 7 has a limitation of 2 CPU which would make total sense since its only seeing 2 cpus. My question is does VB allocated CPUS based upon the host or guest or both?
I'm just trying to figure out the crashes. It appears if set the CPU and Ram parameters Vs the number of VM max per system using only half the CPUS .........she works.
Also Numas 1,3 active, Numa Mode 2,4 not even used. Even if i set tasks to high priority and set affinity to all cores same result.
System is running very fast and stable when the number of CPU was lower but this crash is a concern. last line (VT-x is not available) I'm think because I have no CPU cores left.... which again runs out of CPU cores causing error.
Thanks,
Mike