virtualbox.org

Hi all.
I can't make networking on my guest Ubuntu 9.04.
I have tried NAT and Bridge without success. On guest Ubuntu I setup ip 10.6.68.137 / 24. I'm checking network with ping and telnet <myProxyIp> 3128.
On host windows XP (fresh install) ServicePack3 firewall is disabled, no antivirus software.
Please advice something!

VirtualBOX verison 3.0.4r50677.

About guest Ubuntu 9.04

Code: Select all

VirtualBox Command Line Management Interface Version 3.0.4
(C) 2005-2009 Sun Microsystems, Inc.
All rights reserved.

Name:            ubuntu-1
Guest OS:        Ubuntu
UUID:            1594f169-9def-4724-b3b7-21cef298aeaa
Config file:     C:\Documents and Settings\secret\.VirtualBox\Machines\ubuntu-1\ubuntu-1.xml
Memory size:     384MB
VRAM size:       12MB
Number of CPUs:  1
Boot menu mode:  message and menu
Boot Device (1): Floppy
Boot Device (2): DVD
Boot Device (3): HardDisk
Boot Device (4): Not Assigned
ACPI:            on
IOAPIC:          off
PAE:             off
Time offset:     0 ms
Hardw. virt.ext: on
Nested Paging:   off
VT-x VPID:       off
State:           running (since 2009-08-13T03:20:23.796000000)
Monitor count:   1
3D Acceleration: off
Floppy:          empty
SATA:            disabled
IDE Controller:  PIIX4
Primary master:  D:\VM_Images\ubuntu-1.vdi (UUID: 608ecb6a-467f-418d-9b21-1eaf3b5b21d5)
DVD:             C:\PROGRA~1\Sun\XVMVIR~1\VBoxGuestAdditions.iso (UUID: dd944cd0-0dc3-4037-a729-d6bf2d0ddb25)
NIC 1:           MAC: 080027A00B2F, Attachment: Bridged Interface 'Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller', Cable connected: on, Trace: off (file: none), Type: Am79C973, Reported speed: 0 Mbps
NIC 2:           disabled
NIC 3:           disabled
NIC 4:           disabled
NIC 5:           disabled
NIC 6:           disabled
NIC 7:           disabled
NIC 8:           disabled
UART 1:          disabled
UART 2:          disabled
Audio:           enabled (Driver: DSOUND, Controller: AC97)
Clipboard Mode:  Bidirectional
Video mode:      800x600x32
VRDP:            disabled
USB:             enabled

USB Device Filters:

<none>

Available remote USB devices:

<none>

Currently Attached USB Devices:

<none>

Shared folders:  <none>

VRDP Connection:    not active
Clients so far:     0

Guest:

Statistics update:                   disabled

About Windows XP

Code: Select all

C:\Program Files\Sun\xVM VirtualBox>ipconfig /all

Windows IP Configuration

        Host Name . . . . . . . . . . . . : dit
        Primary Dns Suffix  . . . . . . . :
        Node Type . . . . . . . . . . . . : Unknown
        IP Routing Enabled. . . . . . . . : No
        WINS Proxy Enabled. . . . . . . . : No

Ethernet adapter Local Area Connection:

        Connection-specific DNS Suffix  . :
        Description . . . . . . . . . . . : Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller
        Physical Address. . . . . . . . . : 00-22-15-C9-48-28
        Dhcp Enabled. . . . . . . . . . . : No
        IP Address. . . . . . . . . . . . : 10.6.68.136
        Subnet Mask . . . . . . . . . . . : 255.255.255.0
        Default Gateway . . . . . . . . . : 10.6.68.225
        DNS Servers . . . . . . . . . . . : 10.6.68.4
                                            10.6.68.3

Ethernet adapter VirtualBox Host-Only Network:

        Connection-specific DNS Suffix  . :
        Description . . . . . . . . . . . : VirtualBox Host-Only Ethernet Adapter
        Physical Address. . . . . . . . . : 08-00-27-00-B8-8A
        Dhcp Enabled. . . . . . . . . . . : No
        IP Address. . . . . . . . . . . . : 192.168.56.1
        Subnet Mask . . . . . . . . . . . : 255.255.255.0
        Default Gateway . . . . . . . . . :

Hi,

Here is a little method to re-install VBox under XP to have nice chances to get the bridge working :

-> Uninstall VBox
-> Now, go in your Control Panel -> System -> Hardware and desactivate all your network adapters (even the one you shall use later in VBox)
-> Once this done, install VBox again, and once the installation is done, don't start VBox yet.
-> You can now re-activate your network adapter(s)
-> Now in VBox, select your network adapter used for Bridge in the Network options.
-> Start VBox. If your Ubuntu configuration is set to Auto and your network is configurated as DHCP, this should work.

For Agnitum Outpost Firewall ( but this is not your case ) :

Nat is known to cause problems when Content Filter is activated. You can unactivate it by modifying the machine.ini in C:/Program Files/Agnitum/Outpost.
Find the line "EnableContentHandler" and set the value to FALSE. Save the file and restart the computer.

I really hope this will help you

Keep asking in case it wont ! Cheers

Nope

On fresh windows XP I disable network adapter, install VB, enable network and test = nothing

I disabled both network adapters, reinstall VB (repair), one card was enabled, enableing another, testing = nothing

But in this time I'm tested only bridging.

Strange... Well, i wish i could help more by looking and testing on my own VBox install but im actually at work right now ^^

What you could try now is to remove the VBox Host Interface (look around in VBox options, you should find) and restart to see. I had pretty much the same problem as you on past versions (look at my posted messages) and at the time, this helped me.

I forgot to uninstall VB as you offer. Now I have tried this also without success.

Well well.... What ip does Ubuntu give you for your virtual network adapter ? Give the ip adress, submask and gateway. Try also to give the log of VBox for this VM, if you find the part when it shows the network settings.

Where I can find this log? Should I setup it first?

YAHOOO!!
I have changed vbox network adapter to Intel PRO/1000 MT Desktop and now it WORKS!!

Okey

good news. Enjoy VBox now !

virtualbox.org

NAT & Bridge not working

NAT & Bridge not working

Re: NAT & Bridge not working

Re: NAT & Bridge not working

Re: NAT & Bridge not working

Re: NAT & Bridge not working

Re: NAT & Bridge not working

Re: NAT & Bridge not working

Re: NAT & Bridge not working

Re: NAT & Bridge not working