QNX 6.5.0 not running with 2 cores (6.4.1 did)
-
- Posts: 1
- Joined: 26. May 2010, 11:10
- Primary OS: MS Windows XP
- VBox Version: OSE other
- Guest OSses: QNX
QNX 6.5.0 not running with 2 cores (6.4.1 did)
I was using QNX 6.4.1 on virtualbox with 2 CPUs without problems.
When I tried out QNX 6.5.0 ( M4 and M9 ) I found that only setting up 1 CPU is working
here is the errormessage when running qnxbasesmp.ifs
apic_local_intr.c:212 -- ASSERT((cpu ==0)||(lapic_read(LAPIC_LLOR)&LVT_MASKED)) failed!
CPU 1 start failure
Would be nice, if this setup would be possible again.
Sent a request to QNX support in parallel, because I don't know whether the problem is cause by QNX or VirtualBox.
When I tried out QNX 6.5.0 ( M4 and M9 ) I found that only setting up 1 CPU is working
here is the errormessage when running qnxbasesmp.ifs
apic_local_intr.c:212 -- ASSERT((cpu ==0)||(lapic_read(LAPIC_LLOR)&LVT_MASKED)) failed!
CPU 1 start failure
Would be nice, if this setup would be possible again.
Sent a request to QNX support in parallel, because I don't know whether the problem is cause by QNX or VirtualBox.
- Attachments
-
- screenshot showing the error message
- qnx.JPG (26.29 KiB) Viewed 50168 times
-
- Posts: 9
- Joined: 1. Nov 2011, 21:41
- Primary OS: MS Windows 7
- VBox Version: PUEL
- Guest OSses: windows, linux, qnx
Re: QNX 6.5.0 not running with 2 cores (6.4.1 did)
This is broken for me too, any ideas ?
Thanks,
Boo
Thanks,
Boo
-
- Oracle Corporation
- Posts: 2973
- Joined: 19. Dec 2007, 15:45
- Primary OS: MS Windows 7
- VBox Version: PUEL
- Guest OSses: Any and all
- Contact:
Re: QNX 6.5.0 not running with 2 cores (6.4.1 did)
Probably best to pursue this with QNX. It's not quite clear to me what the assertion means, so all I can say is that no other OS I know of is complaining.
It could be that VirtualBox gets some esoteric aspect of APIC operation wrong, but it's hard to tell what QNX is trying to check for there.
It could be that VirtualBox gets some esoteric aspect of APIC operation wrong, but it's hard to tell what QNX is trying to check for there.
Re: QNX 6.5.0 not running with 2 cores (6.4.1 did)
Any updates on this problem. It seems to be already a year old problem, which I just faced on my environment. Any solutions highly appreciated.
-
- Oracle Corporation
- Posts: 2973
- Joined: 19. Dec 2007, 15:45
- Primary OS: MS Windows 7
- VBox Version: PUEL
- Guest OSses: Any and all
- Contact:
Re: QNX 6.5.0 not running with 2 cores (6.4.1 did)
As an unsupported guest OS, QNX is extremely low on the priority list. So far, no paying customer even asked about QNX support, so the situation is not likely to change anytime soon.Pshem wrote:Any updates on this problem. It seems to be already a year old problem, which I just faced on my environment. Any solutions highly appreciated.
I'll reiterate what I said many months ago - if you are entitled to support for QNX, ask what the assertion means and what exactly VirtualBox is doing wrong. If you just say "QNX doesn't work", we're not interested. If you say "local APIC register so-and-so is incorrectly setting a certain bit under certain conditions", we're much more likely to listen.
-
- Posts: 13
- Joined: 16. Sep 2012, 12:20
- Primary OS: Ubuntu other
- VBox Version: PUEL
- Guest OSses: Windows, Linux, QNX, Haiku, OS X
- Location: Russia
Re: QNX 6.5.0 not running with 2 cores (6.4.1 did)
Pshem
May be changing kernel can fix this problem?
PS: Qnx awful works in virtualbox
May be changing kernel can fix this problem?
PS: Qnx awful works in virtualbox
Re: QNX 6.5.0 not running with 2 cores (6.4.1 did)
has this issue been resolved? what was the solution for this assert?
I am having the same issue with QNX 6.5 with QNX on Intel Atom® E3815, 1.46 GHz, 1 core (TC3: 40)
I have contacted QNX and waiting for response, but this is taking time
I am having the same issue with QNX 6.5 with QNX on Intel Atom® E3815, 1.46 GHz, 1 core (TC3: 40)
I have contacted QNX and waiting for response, but this is taking time
-
- Site Moderator
- Posts: 20945
- Joined: 30. Dec 2009, 20:14
- Primary OS: MS Windows 10
- VBox Version: PUEL
- Guest OSses: Windows, Linux
Re: QNX 6.5.0 not running with 2 cores (6.4.1 did)
'sa', Since Virtualbox is free, you could try it and let us know if the problem is fixed.
Re: QNX 6.5.0 not running with 2 cores (6.4.1 did)
I am not sure how to get VM on that hardware. Right now I don't have any os on that hardware.
I could not install from the QNX cd and I followed up with QNX.
I have received an .bin file from QNX , that i could flash to an USb and boot from USB on that hardware.
I am trying to install QNX on the m2 drive on that hardware, but i am getting the assert message apic_local_intr.c:203--assert((lapic_read(LAPIC_LL0R)&0x700)==0x700) failed
I am following up with QNX on why the .ifs file i generated is having this issue while their .bin file boots fine.
there has been no response lately .
I could not install from the QNX cd and I followed up with QNX.
I have received an .bin file from QNX , that i could flash to an USb and boot from USB on that hardware.
I am trying to install QNX on the m2 drive on that hardware, but i am getting the assert message apic_local_intr.c:203--assert((lapic_read(LAPIC_LL0R)&0x700)==0x700) failed
I am following up with QNX on why the .ifs file i generated is having this issue while their .bin file boots fine.
there has been no response lately .
-
- Site Moderator
- Posts: 20945
- Joined: 30. Dec 2009, 20:14
- Primary OS: MS Windows 10
- VBox Version: PUEL
- Guest OSses: Windows, Linux
Re: QNX 6.5.0 not running with 2 cores (6.4.1 did)
What "hardware" are you referring to?sa wrote:I am not sure how to get VM on that hardware.
Re: QNX 6.5.0 not running with 2 cores (6.4.1 did)
Beckhoff C6015-0010
-
- Site Moderator
- Posts: 20945
- Joined: 30. Dec 2009, 20:14
- Primary OS: MS Windows 10
- VBox Version: PUEL
- Guest OSses: Windows, Linux
Re: QNX 6.5.0 not running with 2 cores (6.4.1 did)
If you are trying to install QNX on the Beckhoff directly, then you have the wrong forum. This forum is for installing operating systems in Virtualbox virtual machines.
If you have a supported OS like Windows or Linux on the Beckhoff, and you've installed Virtualbox, and you're trying to install QNX inside Virtualbox, then we might be able to help.
Is Virtualbox involved in your setup?
If you have a supported OS like Windows or Linux on the Beckhoff, and you've installed Virtualbox, and you're trying to install QNX inside Virtualbox, then we might be able to help.
Is Virtualbox involved in your setup?
Re: QNX 6.5.0 not running with 2 cores (6.4.1 did)
I am trying to install QNX directly on the controller and it doesn't involve virtual box
-
- Site Moderator
- Posts: 20945
- Joined: 30. Dec 2009, 20:14
- Primary OS: MS Windows 10
- VBox Version: PUEL
- Guest OSses: Windows, Linux
Re: QNX 6.5.0 not running with 2 cores (6.4.1 did)
OK, Sorry to have to say it, but this is not the place for you to get help for your project. We would not know how to help.
The original questions in this topic was about installing QNX in a Virtualbox VM.
Hope you can get things running!
The original questions in this topic was about installing QNX in a Virtualbox VM.
Hope you can get things running!