[Solved] Wifislax and chipset Ralink RT3070

[Fielding]

I have installed in VB under w8.1 wifislax last version and install in windows the chipset ralink RT3070.
In windows the chipset is recognised.
But now the vm don't go and receive this message :

Failed to open/create the internal network 'HostInterfaceNetworking-Tarjeta LAN inal?mbrica 802.11n USB' (VERR_INTNET_FLT_IF_NOT_FOUND).
Failed to attach the network LUN (VERR_INTNET_FLT_IF_NOT_FOUND).
Result Code:
E_FAIL (0x80004005)
Component:
ConsoleWrap
Interface:
IConsole {872da645-4a9b-1727-bee2-5585105b9eed}

I have used Attached to Bridged Adapter
and in advanced options there is this :

http://imagizer.imageshack.com/img923/5128/Zc40wR.png

The usb port 2.0 is active.

What can i do now ?

Best Regards

[BillG]

Even If you could bridge to a USB wireless connection on the host it would not look like wireless inside the vm. It would look like an Ethernet connection.

The only way to see it as a wireless connection is to capture the USB device from within the vm. The host will not be able to use the device while it is captured by the guest.

[Fielding]

Thanks BillG. I will inform how the problem was solved in a near future.

Best Regards

[Fielding]

Even If you could bridge to a USB wireless connection on the host it would not look like wireless inside the vm. It would look like an Ethernet connection.

The only way to see it as a wireless connection is to capture the USB device from within the vm. The host will not be able to use the device while it is captured by the guest.

This is what i did :

http://imagizer.imageshack.com/img924/2554/hjCnqb.png

http://imagizer.imageshack.com/img924/114/3aFyhw.png

I can launch the vm and apply a couple of commands to begin to audit

iwconfig

airmon-ng start wlan0

from a linux console.

Best Regards

[Fielding]

The above solution goes well in the laptop.

But the same configuration don't go in the desktop.
Don't recognize the usb device in the desktop.
Then i try and receive this message :

USB device 'Ralink 802.11 n WLAN' with UUID {f1393cab-53ad-4d9c-a21e-c12fc95e79ff} is busy with a previous request. Please try again later.


Result Code:
E_INVALIDARG (0x80070057)
Component:
HostUSBDeviceWrap
Interface:
IHostUSBDevice {c19073dd-cc7b-431b-98b2-951fda8eab89}
Callee:
IConsole {872da645-4a9b-1727-bee2-5585105b9eed}

Failed to attach the USB device Ralink 802.11 n WLAN[0101] to the virtual machine WifislaxMOZ.

If a helping hand knows the answer welcome.
I will give the solution as soon I know.

Best Regards

[socratis]

Please read the following: USB basics and troubleshooting.

[Fielding]

Read.

I have a lack of basis but I will try :

1. deactivate the antivirus relating to the availibility of the usb in the guest, that seems to be occupied by the host
2. Investigate any other process relating to this. And how to locate such processes or services in the host system. Your help - i suppose - give this by known by an expert user in windows.
3. By an economy of time I will try also with vmware.

When I have an answer I will put here.

In General the web offers answers to this problem relating to a minor conflictive vmware, but seems that this environment have similar problems.
Some of the videos and help analized are a simple a lost of time with instructions to nowhere.

Other instructions are in the most genuine line of complicating and large depurated measures to bore any user.

[Fielding]

I tried vmware last version , wifislax and Kali.

I have not problems recognizing the ralink RT 3070

My question is this :

If i have no problem with other virtualization tool have I to try with VirtualBox or is innecesary because fails with the same operating system windows 8.1 ?

In other words : Is useful to try any other measure ?

Best Regards

Where can i find the compatibility list or conflictive drivers with Virtualbox ?

[Fielding]

I considered this post solved, but I was not able to see how edit the main title.

Best Regards

P.D. Finally I see how to edit the main title. ...