So i have this DWA-140 rev. D WiFi usb and i tried to use it in the vm to scan some networks with kali.
This is my first time experimenting with that kind of stuff, usually the "eth" connection from the host is fine.
Now i made a filter for the stick so i plug it in, the os finds the drivers and attaches them. I can see APs in range. Seconds later i get hit with the "Vendor Request 0x07 failed for offset 0x0500 -110" and it stops.
Doesn't come back doesn't fix itself just stops working. It won't try again either just gives up.
Now it works in my host perfectly, both host and guest are updated and i even dragged the driver.bin to the guest just in case the kali one came broken but nothing seems to work.
I am interested in any potential solutions of course but if possible i would also like to understand what happens.
The driver is found, attached and the device works fully. What timed out? We are good just stop and chill. But it won't.And then it will fail. And now you are reading my sleep deprived rambling
dmesg bellow:
Code: Select all
[ 53.984198] usb 1-2: config 1 interface 0 altsetting 0 endpoint 0x4 has invalid maxpacket 512, setting to 64
[ 54.007922] usb 1-2: New USB device found, idVendor=2001, idProduct=3c20, bcdDevice= 1.01
[ 54.007934] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 54.007941] usb 1-2: Product: 802.11 n WLAN
[ 54.007945] usb 1-2: Manufacturer: Ralink
[ 54.007949] usb 1-2: SerialNumber: 1.0
[ 54.461829] usb 1-2: reset full-speed USB device number 4 using ohci-pci
[ 54.969682] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 5392, rev 0223 detected
[ 56.019020] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 5372 detected
[ 56.028205] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 56.137335] ieee80211 phy1: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[ 56.137360] rt2800usb 1-2:1.0: firmware: direct-loading firmware rt2870.bin
[ 56.137362] ieee80211 phy1: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.36
[ 71.253870] ieee80211 phy1: rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x0500 with error -110
Also the ifconfig for the little bit it's up then wlan0 disappears from the list:
Code: Select all
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.0.2.15 netmask 255.255.255.0 broadcast 10.0.2.255
inet6 fe80::a00:27ff:fe3d:e073 prefixlen 64 scopeid 0x20<link>
ether 08:00:27:3d:e0:73 txqueuelen 1000 (Ethernet)
RX packets 91 bytes 29027 (28.3 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 107 bytes 12933 (12.6 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 8 bytes 400 (400.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 8 bytes 400 (400.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 36:d3:79:8e:bd:57 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0